computer science and technology

The troubleshooting usulay met when after refilling cartridge

2008-01-23T08:51:00.000+07:00

When return the cartridge to tested, if glimmer indicator lamp the result and doesn’t responsive like we are command to printing, so steps must be done :

- Unpluge the usb cable (pc- printer conector cable)

- Unpluge the power cable

- Open the printer cover

- Press the power button and don’t removed

- Connect the power cable to electricity grid

- Hold power button between 5-10 secon then removed

- Press power button again for turn on the printer

- Closed the printer cover

- Wait until the printer normal return

- Ascertain normal printer returns by unpluge power cable and turn on again

- When does printer not show indicator lamp is glimmer so printer is normal

- When does indicator lamp is glimmer repeat the all steps to success.

After several times ink admission fillings, usually cartridge unknow by computer. This matter is posibility because full ink getter sponge. So that sponge necessary washed, then do reset as usual.

Refill ink steps

2008-01-04T10:47:00.000+07:00

Cause by various model kind cartridge, various also method to refill. If the refill ink by injection, next are steps to following fo refill the ink by injection :

- Prepare device that is tissue that functioned to absorb and clean if the ink is over flow or spilled and prepare advice to make the hole on cartridge to put into needle to cartridge. But casually every ink refill enclose key punch. And importantest prepare appropriate ink with brand and printer kind or kind your cartridge.

- Several kinds of cartridge usually place to put into ink has passed this hypodermic needle prepared. The place on top and closed with label. Open label then make hole points part on the center.

- Take injection, then fill ink that be injected. Afford capasity of ink in injection not excessive. Suit with the capasity. Or if you applying for injection ink with injection tool, when to inject the ink do with slowly and carefull, don’t until overflow, if feel enough, stop to inject. End with unplug ink injection tool.

- Cleaning ink if overflow by kleenex. After that close the hole with cellophane tape. And cartridge alredy to used.

Those steps also applied in colour ink. But don’t fill the colour ink is wrong. Because if we have fill ink colour, will have the result of print disagree with colour we wanted. This matter cause colour has been mixed in cartridge. Than finish your printer ink refill steps.

The reason, why can person the printer ink contents self ?

2008-01-03T17:00:00.000+07:00

Although there are level indicator for ink contents capacity in cartridge, but that only estimate that given computer. Surely we still not yet can determine to how much sheet again ink contents that still can be used.

A moment printing requirement on the day time we may not more disappointed when fresh out of ink, because can be going to ink fill service, however if you need at night (midnight) there is no store that open.

Well moment like here's our ability in refill printer ink self need so much. Cause we enough to prepare reserve ink in the bottle only. So anywhen the ink is fresh out, we are direct can fill self without play around with delaying work (“remember time is money”).

Apart from reason also there moment when we exploit ink refill service, we don't know is ink packed into by cartridge as according to maximal capacity from cartridge itself. If not appropriate, would increasingly adds expensive of ink refill. However if we can fill the ink self, so how much the many the ink can be filling, that is cost we pay.

The Difference of Pentium D and Pentium Dual Core

2007-12-24T07:41:00.000+07:00

Pentium D still based on core netburst from technology Pentium 4 earlier. While Pentium Dual Core series E2xxx has based on core Allendale from core architecture which newest. So, Pentium Dual Core better beside the performance is compared Pentium D, Athough Pentium D work at quicker clock. Both types of this processor has owned two cores processor in it.

Technics Taken Care Of Printer (Part 8 - end)

2007-12-11T18:00:00.001+07:00

Faces damage printer

In general, your weapon takes care and solves the problem emerging at inkjet printer is manual book of printer, and telephone number of consumer service from vendor maker printer which you applies. Most the problem at your printer you can handle by following stages of steps guidance provided at manual. Manual also usually provides common guidance takes care of printer.

Guidance overcomes problem at printer generally different between printer, even in one the same brands, so we are not possibly to discuss it in this short article. Our suggestion, read accurately manual accompanying printer which you have.

Although there is nothing problem, when first time opens the hardboard of printer after buying it, read formerly manual before conducting action anything. Manual usually explain things required to you to pay attention to, takes heed, or do.

If meets problem which haves not to handle by your self, and manual doesn't explain it detailedly you can phone to consumer service which they provide. If have been very hard and you surenders, the last choice is bring to center service closest.

Technics Taken Care Of Printer (Part 7)

2007-12-01T07:32:00.000+07:00

Turn off when the printer is not used

This thing also need to be paid attention is action to turn off printer. Turn off the printer otherwise is applied during stripper. Example, turn off printer in office hours end. Turn off done not with directly to abstract the power cable of printer, but by button 0n/off at printer.

Turn off printer when is not applied can prevent runs dry it is inking at nozzle. At all of printer inkjet there are working certain mechanism protects head print from the air external when printer is turn off. Side effects from turn off printer is electrical thrift, although economical of course not many, because new printers generally have been economizing energy power.

Technics Taken Care Of Printer (Part 6)

2007-11-27T08:21:00.000+07:00

With manual cleanning

To clean head at cartridge in manual. You must discharge it from the place in printer. Its way different depended the printer. For HP printer, for example turn on the printer and open the printer cover, then automatically ink cartridge moved to middle.

Before discharging cartridge, ascertains printer has been turn off by abstracting power cable from electric socket. Discharges cartridge carefully then puts on the table. Use cotton bud, doesn't use alcohol, then cleaned head with cotton bud.

Cleaning process with cotton bud must be slowly. Doesn't sweep cotton bud to plate nozzle. Pays attention to if there are lag dirt in plate nozzle and part of other cartridge. This cleaning process same as before all. For head cartridge is having colour, use only one cotton bud for monochrome to avoid transfer of dirt. After completed resets cartridge to it place in printer.

If still had not setled, prepares hot water around 3/4 transparent/plastic glasses (can be taken away from dispenser) then glued part of nozzle - only part of this only, not all water level cartridge bodies during around 5 minute.

You will see ink exit to the water. Don't fear, your ink will not used up. When inking stream to water has started is fluent may simply nozzle/head also have been enough cleanness. Then lifted cartridge, and dries with cotton bud or smooth cloth.

Beside keep cleaning head, also need to be taken care of is ink don't really used up. When cartridge runs out of ink, resistor in the head can be fired. Most of printer will remind the user when cartridge will run out of ink.

Technics Taken Care Of Printer (Part 5)

2007-11-21T07:29:00.000+07:00

Cleaning with help of utility

Almost every printer provides feature to clean head using paper with pressing one of button to click one of button in management menu of printer from computer which connect to printer.

Utility management of this printer you can get from dialogue box properties for printer which you to use (from Start searching control panel, then select printer, right click and select properties from emerging menu list). At properties menu you can get utility to manage your printer, including to clean the cartridge. For farther information, you can read the manual book of your printer.

Step of cleaning with utility management of this printer can be doing for first step every time you found existence of handicap at result of print. This cleaning need to do if you have been long time didn't use a printer - for example, more than one week.

That need to be paid attention, don't have ever do clean the head (its intention nozzle at head) twice or more successively, because exactly will make dirtier head. After cleaning the head with utility management printer, try to print, or do attempt printing.

Then wait for a few minutes. Print two or three pages contains colour pattern with well-balanced colour. Because this will keep away the water bubbles, or possible foamy ink because of cleaning process. After that, if result of the print still not good, then you might to doing clean again.

Technics Taken Care Of Printer (Part 4)

2007-11-15T07:40:00.000+07:00

Inner cleaning

To clean interior printer, used a small paintbrush and dirt straw portable to clean a dust in interior printer. Remembers, the ink residue not necessarily be cleaned. This residue will not effect. Even if you try clean it, more than used the material like alcohol, can be destroy your printer. Don't forget to use Iubricant for the metal bar become ink rail.

In interior printer, one other sometime need to be cleaned is catridge ink. Cleaning this part enough important to do it if you found quality of streaky print without the colour, or there are ink excess impression in certain part.

Technics Taken Care Of Printer (Part 3)

2007-11-12T16:43:00.000+07:00

Cleans surface

Besides using it is regularly, printer would increasingly durabel, and seen good if diligent is cleaned. Cleaning regularly will repair the appearance is at the same time prevents incidence of problem.

To clean surface printer, familiarizes you to clean part of surface of outside printer whenever you changes cartridge ink. For this work, using soft barium cloth ( hose barium or like cloth to clean eyeglasses), and labours so that doesn't cause improvement of humidity in interior printer.

Technics Taken Care Of Printer (Part 2)

2007-11-10T19:37:00.000+07:00

Often to applied.

To make your printer durabel there are one steps that is possible without realizes you has done, that is using it is regularly every day. Many people, mainly because requirement of print which not many and fear for pays the price of ink that is expensive, lets the printer is old not to applied.

Printer is not decorator beside your computer, but thar is which must be applied regularly, applies printer regularly will make it works consistently and obviates it from problem.

Technics Taken Care Of Printer (Part 1)

2007-11-09T22:30:00.000+07:00

New generation of printers are more and more bright. The ability taking care of self also increasingly good. But do not mean you are not at all the need of takes care of it, it is of course you doesn't wish fund released to become useless, because goods as expensive and as good as anything the performance is remain to requires treatment which continue.

Possibly still considering health advice " prevents is better than at curing"?. This advice also valids for printer. Takes care of printer will make it more durabel, and more doesn't have problem. Printer which you buys with the price of approximately 500 thousand, possibly requires repair closing the original value when breakdown.

Main problem of printer of course relates to main work of this printer, that is ink and head, for example can cause ink cannot reach paper and gives ugly print result, the other problem of which could probably bother your printer are adaptor and mechanic ( motor), but both this problems seldom happened.

Know the problem in your computer .....!

2007-11-07T22:38:00.000+07:00

The problem of PC is because of damage hardware at one particular PC can be known from sound beep that taked pc. In the table follows to be damage sign in pc in general, and Especially for device that has bios in your pc brand is " Award" , Look at sound beep that taked speaker pc.

Beep 1x short	No problem
Beep 1x long	The problem in hardisk
Beep 1x long and 1x short	The problem in motherboard
Beep 1x long and 2x short	The problem in VGA
Beep 3x long	The problem in keyboard
Beep short continual	The problem in power supplay
Beep long continual	The problem in memori